Insulation fixings
Metal anchors
Plugs and fixings
Direct fastening
Nailers and accessories
Chemical anchors
Clamps and clips
Profiles and accessories
Screws
Fixings accessories
What is driving rain?
Source: www.pfb-rosenheim.de
Driving rain is a combination of rain and wind.
This article explains why driving rain can be problematic, the test procedure for driving rain tightness - especially with reference to DIN EN 1027 - and the products you can use to ensure driving rain-proof façade fixings.
Watertightness against driving rain using the example of the ResiTHERM® 16 distance mounting system
Problem:
The wind creates pressure that pushes the water against the fixing point.
If this is not sealed, there is a risk of water penetrating the façade due to driving rain. This can result in mould growth or, in the worst case, destruction of the plaster, frost damage and damage to the building fabric, as explained in our article about thermal bridges.
Therefore, the usage of driving rain tight (synonym for rainproof) products is of great importance - especially for fastening products that are to be installed on the façade.
Testing for driving rain tightness
During the test, a test frame containing the plastered insulation board with the installed products is installed in the test chamber. Then the sprinkling is started in the resulting testing room and the pressure is increased stepwise, following DIN EN 1027. The highest pressure level is an overpressure of 600 Pa, which corresponds to wind force 11 (Beaufort scale) or, in other words, a hurricane-like storm.
After the test period of 55 minutes, the test frame is removed, the products will be screwed out and the institute assesses whether or not water has penetrated the insulation.
Test procedure with reference to DIN EN 1027
This European standard regulates the procedure and requirements for the test.
For example, the test is carried out under the following conditions:
- A water spray system wets the entire surface of the test element
- In a special measuring chamber whre the amount of water and the pressure is conrolled and regulated
DIN EN 1027 provides for two different installation methods:
Method A
Installation without structural protection: The installed products are thus completely exposed to the weather.
Method B
Installation with structural protection: The installed products are protected from the weather by porches, balconies etc.
Test procedures for CELO's products:
Products tested according to procedure A. During the test, the test pressure is increased stepwise with defined preassure and time steps acc. EN 1027.
The products were tested up to 600 Pascal (Pa) - see above test procedure with reference to DIN EN 1027.
The test is passed if no moisture enters the insulation material.
TEST RESULT: Watertight agains driving rain using EN 1027 (method 1A). For further specifications, e.g. the plaster grain size, please refer to the brief report:
Driving rain-tight insulation anchors from CELO
As a specialist with 60 years of experience in the fastening industry, CELO develops high-quality fastening solutions that save the installer assembly time and therefore money.
You can recognise CELO's innovative insulation products that have passed the driving rain tightness test according to DIN EN 1027, procedure A, by this symbol:
.
Energy-efficient driving rain-tight (rainproof) products from CELO:
The insulation anchors and screws from CELO are not only driving rain-tight, but also ensure thermal separation, are made of ageing-, weather- and UV-resistant nylon and are halogen-free.
The entire insulation range of fixing to the insulated façade is manufactured at the company's site in Aichach (Bavaria, Germany) - so it is guaranteed Made in Germany.
Here you will find our tested driving rain-tight product range:
Isolation plug IPL 95DS
Insulation screw IPS 80
Insulation screw plug IPSD 80
Insulation screw IPS-H 55
Insulating screw plug IPSD-H 55
Further information
The simple insulation fixing selector
How to find the right solution for your attachment to the insulated façade! Light-weight applications, canopy or balcony? Wood fibre board or polystyrene? Go step-by-step to find the right product, including load values.
Why you should avoid thermal bridges?
Find out here why avoiding a thermal bridge is important and how you can save heating costs and maintain the energy efficiency of your building with the right fixing solutions.
Playlist: This is how quickly and easily you install the insulation fasteners from CELO
The insulation plugs and screws from CELO are not only free of thermal bridges and UV-resistant, they are also installed in no time at all. In short videos, we show you how to mount cap strips, signs, awning brackets or downpipe clips on the thermal insulation.
Everything you need to know about the innovation ResiTHERM® 16 & 12
What is the advantage of ResiTHERM® 16 or 12 for heavy-duty fastening on insulated facades? Including descriptive installation videos and an overview of the sets and accessories!
All insulation fixings available at a glance
CELO offers you time-saving solutions that provide thermal separation at the same time. Take a look at the special solutions for the installation of French balconies, satellite dishes or wall connection profiles.
ResiTHERM® 16 Our services online and on site
Convince yourself of our innovative product with ETA for driving rain-tight installation on insulated façades! Request a free demo, online seminar, additional information material or, non-binding offer or request a free product sample.
Do you have any questions about the driving rain-proof range from CELO? Can we help you find the right accessories for your application?
Our professional team is available for technical advice during telephone hours. Feel free to write us your request via the contact form and we will answer you as soon as possible!
